What You’ll Pay for Vanities, Tile & Fixtures in Bonita Springs
A vanities, tile, and fixtures project in Bonita Springs typically runs $5,000 to $18,000, depending on whether you’re swapping a single vanity and resurfacing a backsplash or gutting the wet wall, moving plumbing, and installing floor-to-ceiling porcelain with a custom double vanity. Most jobs that include a new vanity, new tile floor, new shower wall tile, and fixture replacement finish in 5 to 9 working days. Call us at (844) 638-7249 to set up a free on-site estimate with a line-item breakdown of your specific scope.
How We Handle Vanities, Tile & Fixtures in Bonita Springs
The sequence matters. We’ve run hundreds of these jobs in Lee County homes and the order of operations either saves you a week or costs you one. Here’s how it actually goes.
Day 1 - Demo and plumbing assessment. Our crew removes the existing vanity, pulls up old tile, and takes out the toilet if floor tile runs underneath it. We shut water at the angle stops and cap supply lines. This is the point where we confirm whether the plumbing is in the right location for your new vanity or if we need to move drain and supply lines. An older Bonita Shores home with cast-iron drain pipes in a concrete slab will add time here. We also check for any water damage behind the old tile backer board. You’ll have already chosen your new vanity, tile, and fixtures before we swing a hammer.
Days 2-3 - Rough plumbing and substrate prep. This is the stage most people don’t see but that determines how long the tile lasts. If we’re relocating a vanity drain line or moving a shower valve, the plumber does it now while the walls and floor are open. We install cement backer board on any shower or wet-area walls, tape and mortar the seams, and float the floor if the slab is uneven. A house in Pelican Landing built on a post-tension slab with minimal settling moves faster here than a 1970s concrete block home near the Imperial River where the slab has shifted half an inch over 40 years.
Days 4-6 - Tile installation. We lay floor tile first, then wall tile. Your specific tile choice dictates the pace here. Large-format 24×48 porcelain plank goes down faster than a herringbone marble mosaic, but it also leaves less room for error on a floor that is not perfectly flat. We use a Schluter uncoupling membrane on concrete slabs to prevent cracks from transferring through to the tile. Grout happens on the last tile day and needs 24 hours to cure before anyone walks on the floor.
Day 7-8 - Vanity install and fixture trim-out. The new vanity goes in, we mount the countertop and sink, and the plumber returns to set faucets, reconnect the p-trap, and install the toilet. We mount mirrors, towel bars, and any glass shelving you’ve chosen. If you’re doing a new light fixture above the vanity, we coordinate our electrician to handle that while the mirror is off the wall. Every fixture gets tested for leaks, hot and cold water, and drain flow before we call it done.
Day 9 - Final walk-through and cleanup. We remove all debris, run a HEPA vac through the bathroom, and wipe down every surface. You walk the job with the project lead and note anything that needs a touch-up. Our 730-Day Done Right Promise means if a tile grout line cracks or a vanity door goes out of alignment within two years, we come back and fix it.
The Options You’ll Choose Between
Every vanities, tile, and fixtures job comes down to a handful of decisions that drive both the look and the cost. Here are the ones that matter most in Bonita Springs homes.
- Vanity construction. A stock big-box vanity in standard 24, 30, 36, 48, or 60-inch widths costs the least and gets the job done, but the drawer slides and door hinges wear faster in Florida’s humidity. A semi-custom KraftMaid vanity with soft-close, full-extension drawers and a plywood box holds up better long-term - we install these with moisture-resistant finishes specifically because Bonita Springs bathrooms without good ventilation develop swollen MDF cabinet bases within three years.
- Countertop material. Cultured marble is the entry point and works fine for a guest bath that sees light use. Quartz costs more but resists staining, scratching, and the mildew that wants to colonize every porous surface in coastal humidity. Natural stone like marble or travertine looks beautiful but requires sealing every six to twelve months in a bathroom that gets daily shower steam.
- Tile selection. Porcelain is the workhorse for Florida bathrooms because it absorbs almost no water and does not care about the humidity. Ceramic costs less but chips more easily during install. Glass mosaic makes a striking accent wall but runs the highest per-square-foot labor cost because every sheet has to be set perfectly level, and the thinset color shows through if the installer rushes it.
- Floor layout and size. Large-format tile means fewer grout lines to clean and a more modern look, but it demands a dead-flat floor. A diagonal pattern or a running bond with a rectified edge adds material waste and labor hours. If you’re in an older Bonita Springs slab home where the floor has a slight pitch, a smaller 12×24 tile is more forgiving and looks better when installed correctly.
- Fixture finish and valve type. Brushed nickel and matte black are the two most common finishes right now, and Kohler pressure-balanced shower valves are our go-to for reliable temperature control. If you want a rain head and a handheld on separate volume controls, that adds a diverter and more plumbing in the wall - doable, but it moves the budget up and adds a day.
What Vanities, Tile & Fixtures Costs in Bonita Springs, FL
A straightforward vanity-and-faucet swap with a new toilet and a basic tile floor runs $5,000 to $8,000. At the upper end, a job that includes moving a vanity drain line, installing a custom double vanity with a quartz top, tiling the floor and a full shower surround in large-format porcelain, and replacing all fixtures and lighting lands at $14,000 to $18,000. The variables that move the number are the same across Bonita Springs, but the starting point differs house by house.
The biggest cost driver is whether the plumbing stays put. If your new vanity has a different drain center than the old one and the home sits on a concrete slab, cutting and relocating a cast-iron drain line adds hundreds in labor and triggers a plumbing inspection. The second factor is tile square footage and pattern complexity - a 40-square-foot floor and a 70-square-foot shower surround with a simple grid layout costs less in labor than the same footprint with a herringbone mosaic accent band. The third is the vanity itself: a stock 48-inch cabinet with a cultured marble top runs under $2,000 for material and install, while a custom-painted KraftMaid double vanity with a quartz top and undermount sinks lands closer to $5,000. Fixture grade is the fourth variable - a Kohler single-handle shower trim kit costs less than a thermostatic valve system with separate volume controls and a rain head.
Our written estimate separates material and labor line by line. It includes demo, disposal, substrate prep, all tile-setting materials, vanity and fixture installation, a plumbing rough-in if required, and the final trim-out. Permits, if needed, are itemized separately. What it does not include, and what we flag before you sign, is any water-damage repair discovered after demo - rotted subfloor or mold behind an old shower surround gets addressed with a change order and photos before we proceed. Call (844) 638-7249 for upfront pricing specific to your bathroom.
What Bonita Springs Homes Specifically Do to This Job
Bonita Springs bathrooms carry a set of conditions we simply do not see the same way in Estero or Naples. The older concrete-block stock east of US-41, particularly in the Bonita Shores and Bonita Springs Estates neighborhoods, was built before Florida’s post-2004 wind and moisture codes tightened. That means exterior bathroom walls often lack a proper vapor barrier, and decades of humid air pushing through block have rusted out countless medicine cabinet bodies and swollen drywall behind the tile. We regularly open a shower wall in a 1978-era Imperial River-area home and find the green board behind the tile has turned to chalk. A vanities, tile, and fixtures job in one of these houses is rarely just a surface swap - it almost always involves cutting back to the studs and installing cement board and a waterproof membrane before any new tile goes up.
The other uniquely Bonita Springs reality is the post-Ian FEMA substantial-damage determination ripple effect. If your home is in an AE flood zone and you’re pulling a permit for a bathroom renovation that includes moving a wall or relocating plumbing, Lee County may review whether your cumulative post-storm renovation value triggers the 50% threshold that requires elevating the entire structure. A handful of our vanities, tile, and fixtures jobs in the lower Imperial River corridor have been structured as like-for-like swaps specifically to avoid tripping that threshold while homeowners wait for clarity on their FEMA status. We navigate this with you before the permit gets pulled, not after. For a full-scope renovation that goes beyond the bathroom, see our Bathroom Remodeling in Bonita Springs page.
The newer master-planned communities like Bonita Bay and Palmira present a different challenge: the HOA often requires pre-approval for any plumbing work that involves cutting into a shared wall, and some associations mandate specific sound-dampening underlayment beneath tile floors in upstairs bathrooms. We handle the paperwork and know what each community requires before we order materials.
Serving Bonita Springs, FL - Our Local Coverage Area
We’re based in the Bonita Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Vanities, Tile & Fixtures in Bonita Springs
Most projects finish in 5 to 9 working days. A single-vanity swap with a basic tile floor and no plumbing relocation can be done in 4 to 5 days. Adding a full shower tile surround, moving a drain line, or working with a large-format tile that requires precise floor leveling pushes it to 8 or 9 days. The biggest variable is what we find behind the old tile - water damage in an older Bonita Springs block home adds a day or two for substrate replacement.
If you are swapping a vanity and fixtures without moving any plumbing or electrical, Lee County generally does not require a permit. The moment a drain line, supply line, or electrical box moves, you need a plumbing or electrical permit and an inspection. We pull permits on your behalf and schedule inspections so the job stays code-compliant without you chasing paperwork. Some Bonita Springs HOAs, particularly in Pelican Landing and Palmira, require their own architectural review even for non-permitted work, and we submit those applications as part of our start-up process.
Yes, if you have the wall width and the plumbing can be reconfigured. A standard single vanity is 24 to 36 inches wide with one drain center. A double vanity is typically 60 to 72 inches wide and needs two drain centers spaced at least 30 inches apart. In a Bonita Springs slab-on-grade home, adding a second drain line means cutting into the concrete floor, running new pipe, and patching the slab - which adds cost and time but is routine work for our crew. We measure the available wall, check for vent stack clearance, and give you an exact price before any concrete is cut.
Porcelain tile with a water absorption rate under 0.5% is the best choice for Florida bathrooms. It does not warp, swell, or harbor mold the way natural stone can in constant humidity. We recommend a matte or textured finish on floor tile for slip resistance. For shower walls, a rectified-edge porcelain with a tight grout line and an epoxy grout gives you the longest maintenance-free life. If you want the look of marble without the upkeep, porcelain slabs that replicate Calacatta or Carrara veining are widely available and cost less installed than real stone.
Every job we complete is backed by our 730-Day Done Right Promise - if anything related to our workmanship fails within two years, we repair it at no charge. That covers grout cracking, tile lippage, vanity door alignment, drawer slide failure, and fixture leaks from connections we made. Manufacturing defects on the vanity, tile, or fixtures themselves fall under the manufacturer’s warranty, and we handle the claim and the replacement labor so you are not stuck navigating it yourself. Call (844) 638-7249 if you have a warranty question about a past project or want details before you book.
Matching discontinued tile is difficult, but we start by pulling a sample and cross-referencing it with our suppliers and national tile locator services. If an exact match is not available, we source a complementary tile that blends with the existing floor and create a transition that looks intentional rather than like a patch job. In many cases, homeowners end up choosing to replace the whole floor at that point because the cost difference between a partial match and a full new floor is smaller than most people expect. We will give you both options with pricing so the call is yours.
Get a Free Estimate for Vanities, Tile & Fixtures in Bonita Springs
We will come to your home in Bonita Springs, take measurements, talk through vanity, tile, and fixture options that fit your space and budget, and hand you a written estimate with line-item pricing before we leave. The number you see is the number you pay - upfront pricing, no surprises. Our bathroom remodeling crew is background-checked, uniformed, and answers to you from first cut to final wipe-down. Some homeowners pair this work with exterior upgrades like Tile Roofing in Bonita Springs or Specialty Roofing in Bonita Springs when tackling a full exterior refresh. Call (844) 638-7249 to schedule your free on-site estimate.
Written by Derek Hollenbeck, Owner at Groundwork Construction Co., serving Bonita Springs since 2014.