Why Fort Myers Homeowners Choose PGT Construction
If you own PGT windows or doors in Fort Myers and need them repaired, retrofitted, or replaced, we handle the work start to finish - no subcontractors, no runaround. Groundwork Construction Co. of Fort Myers is an independent PGT service provider, not a factory-authorized dealer, which means we give you straight advice on what your specific WinGuard or EnergyVue units actually need without pushing a product line that doesn’t fit your opening or budget. Our crews have pulled, re-glazed, and reinstalled hundreds of PGT impact units across Lee County, including the exact NOA-certified models required for wind-borne debris zones along the Caloosahatchee River. Call (844) 638-7249 to schedule a free estimate on PGT repair in Fort Myers - we answer the phone 24/7, not with a voicemail tree.
Why Trust Groundwork Construction Co. of Fort Myers for Your PGT Construction?
Derek Hollenbeck, our owner and general contractor, learned his trade at Lorenzo Walker Technical College in Naples and has worked construction in Lee County for over two decades - long enough to know which PGT components fail first in Fort Myers’s salt-and-humidity environment and exactly how to fix them without unnecessary replacement. Our technicians have handled WinGuard aluminum-sill weep failures in McGregor corridor ranch homes, delaminated laminated glass in Caloosahatchee riverfront condos, and Eze-Breeze track binding in lanai enclosures across Gateway and Cape Coral Pgt service areas. We use genuine PGT sashes, balance cartridges, and weatherstripping assemblies whenever impact rating or structural integrity is involved. For non-structural wear items like glazing beads or interior trim, we source precision-matching aftermarket parts to control your cost without compromising fit. Every PGT repair we perform is backed by our 730-Day Done Right Promise - if it isn’t done right, we make it right. That’s one of the longest workmanship guarantees in Southwest Florida residential construction.
Common PGT Construction Problems We Fix in Fort Myers
Fort Myers’s particular combination of salt spray, high humidity, and hurricane-driven rain creates a distinct set of failure patterns in PGT products. These are the issues we see most often during service calls across the city:
- WinGuard laminated glass seal failure and interior fogging. The multi-layer laminate in PGT’s WinGuard impact glass relies on an edge seal that breaks down under prolonged humidity cycling. We see this frequently in homes within a mile of the Caloosahatchee - the seal fails, moisture penetrates between the glass and laminate interlayer, and the window develops a permanent haze or visible water droplets between panes. The fix is a replacement laminated insulated glass unit matched to the existing sash. You don’t need a whole new window.
- Eze-Breeze vertical slider binding and track jump. PGT’s Eze-Breeze sliding vinyl panels use a felt-like pile weatherstripping in the side channels. Fort Myers’s fine-sand environment wears that weatherstripping down fast, and once it’s compressed or stripped away, the panel slaps against bare aluminum when it moves. We have replaced panels where the bottom rail had actually climbed out of the lower track because the worn weatherstripping couldn’t keep it seated. The repair is new OEM pile stripping and a track realignment - no panel replacement unless the frame is bent.
- WinGuard aluminum frame weep hole clogging and sill corrosion. PGT engineered small weep slots into the bottom rail of WinGuard aluminum frames to drain wind-driven rain. In Fort Myers, those slots clog with a paste of salt, fine sand, and pollen. Water backs up inside the sill channel and corrodes the aluminum from the inside out. We have pulled sashes on 12-year-old WinGuard units and found the sill completely eaten through beneath a perfectly intact exterior powder coat. You catch this early by cleaning weep holes twice a year - and if the sill is already pitted, we replace it before the frame loses structural integrity.
- EnergyVue low-E coating blotching near the coast. PGT’s EnergyVue insulated glass uses a microscopically thin low-E metallic coating inside the airspace. When the outer edge seal degrades - which happens faster in Fort Myers’s salt-air zones - moisture reaches that coating and triggers a blotchy, rainbow-like oxidation pattern between the panes. It looks cosmetic at first, but it signals that the argon fill has escaped and the insulating value is dropping. We replace the IGU; the frame and sash are typically reusable.
- WinGuard block-and-tackle balance failure on single-hung sashes. PGT uses a specific block-and-tackle balance cartridge inside WinGuard vinyl single-hungs. After seven to ten years of daily use in a humid climate, the internal spring fatigues and the sash either won’t stay up or drops hard when released. This is a straightforward cartridge swap - we stock the exact PGT-spec balance assembly in our local inventory, so the repair typically takes under an hour per sash.
PGT Parts & Our Repair-vs-Replace Approach
We stock genuine PGT replacement sashes, balance cartridges, weatherstripping profiles, and laminated IGUs locally in Fort Myers and for Pgt service in Lehigh Acres so we can complete most PGT repairs in a single visit. For structural components - anything that affects the window’s Miami-Dade NOA impact certification - we use PGT OEM parts exclusively. For non-structural wear items like interior glazing beads, trim strips, and certain exterior snap-on covers, we often source precision-matching aftermarket equivalents that fit the same extrusion profile at a substantially lower cost. We will always tell you when repair is the smarter call and when an older single-pane or delaminated unit is safer to replace. If the frame is pitted, the laminate has separated at the edge, or the unit predates Florida’s 2002 building code wind standards, replacement is almost always the right choice - and we will write you a fixed, no-surprise quote with 0% financing available for 18 months on projects that qualify. Call (844) 638-7249 and we’ll walk you through the options - no obligation, and the estimate is free.
Our PGT Service Process - Step by Step
- 1
On-site diagnosis. We arrive in uniform, check your PGT unit’s glass, frame, weatherstripping, balance system, and weep drainage. We identify exactly what failed and why - not just the symptom. If it’s a WinGuard laminated seal failure, we confirm it with a moisture meter before quoting an IGU swap.
- 2
Quote and parts match. We write you a line-item estimate for the repair or replacement. If OEM parts are required for your PGT WinGuard or EnergyVue unit, we verify the exact model and glass package from the label etched into the corner of the glass or stamped on the frame. We never guess on specs - an impact window’s NOA number has to match the opening.
- 3
Repair or installation. We pull the sash, replace the failed component (IGU, balance cartridge, weatherstripping, or corroded sill), reassemble, and verify alignment. On full impact window replacements, we set the new PGT unit in the rough opening, flash it to Fort Myers wind-driven rain standards, and secure it to hurricane-strap-ready framing per Lee County code.
- 4
Water-shed and operation test. We cycle the window ten times, check the weep drainage with a small water test, and confirm the balance holds at mid-travel. We do not leave until the window operates smoothly and the sill drains correctly.
- 5
Warranty walkthrough. We explain what was done, what parts were used, and how our 730-Day Done Right Promise covers the work. If anything goes wrong in the next two years, we fix it - no runaround.
PGT Products We Service & Install in Fort Myers
Our crews work on the full PGT residential lineup common in Southwest Florida, including Pgt repair in Bonita Springs: WinGuard Vinyl Impact Windows (single-hung, horizontal roller, and picture), WinGuard Aluminum Impact Windows (casement and fixed-lite configurations typical in mid-rise condos), EnergyVue Insulated Glass Windows (low-E argon-filled units popular in newer master-planned communities), and Eze-Breeze Sliding Vinyl Panels (widely used on screened lanais and pool enclosures from Iona to Gateway). We stock common WinGuard balance cartridges, weatherstripping profiles, and standard-size laminated IGUs locally in Fort Myers for fast turnaround on same-sash repairs.
We Also Service These Brands
While PGT is the focus of this page, our multi-trade crews at Groundwork Construction Co. of Fort Myers install and service a full catalog of trusted building brands: we build kitchens with KraftMaid cabinetry and Cambria, Silestone, or Kohler countertops - so when your PGT window repair is part of a larger remodel, you are working with one contractor who handles everything from impact glazing to finished millwork under one fixed-price contract.
FAQs - PGT Construction Service in Fort Myers
No, we are an independent service provider - not a factory-authorized PGT dealer or warranty center. That independence means we give you honest recommendations based on what your specific window needs, not what a manufacturer program requires us to sell. For structural components and anything that impacts your NOA wind certification, we source PGT OEM parts directly.
Yes - whenever the repair affects the window’s impact rating, structural integrity, or water-shedding design. We use genuine PGT sashes, block-and-tackle balance cartridges, laminated IGUs, and OEM weatherstripping profiles. For non-structural wear items like interior glazing beads or snap-on trim, we can source precision-matching aftermarket equivalents that fit the same extrusion and cost you less. We explain the difference in your quote so you know exactly what you are paying for.
In most cases, you can replace just the laminated insulated glass unit - you do not need a new sash. If your WinGuard frame is structurally sound and the laminate delamination or seal failure is confined to the glass pack, we swap the IGU, which preserves your existing frame, weatherstripping, and installation seal. If the frame is pitted with corrosion or the sash welds are cracked, we will tell you honestly and quote a full sash replacement. Call (844) 638-7249 for a free, no-pressure assessment.
Probably not. Stiff Eze-Breeze panels in Fort Myers are almost always caused by worn-out pile weatherstripping that has compressed, swollen with humidity, or packed with fine sand. When the weatherstripping binds against the track, the panel fights you the whole way. We pull the panel, clean the track channels, install fresh OEM weatherstripping, and the slider typically moves with two fingers again. Track replacement is only needed if the aluminum channel is bent or gouged - which we see far less often than simple weatherstripping failure.
It depends on the existing window’s mounting style and the condition of the perimeter seal, but in many Fort Myers homes - especially concrete-block construction from the 1960s through 1980s along the McGregor corridor - PGT impact windows can be replaced from the interior after removing the interior trim and sill without disturbing the exterior stucco at all. We assess each opening individually and explain exactly what the installation will involve before we break ground on anything.
PGT-related work varies widely depending on whether we are repairing a single sash or replacing every window in the house. Here are the typical project ranges we see in Fort Myers:
| Service | Typical Fort Myers Price Range |
|---|---|
| Impact Window Installation (PGT WinGuard) | $8,000 - $25,000 |
| Window Replacement (multiple units, mid-grade) | $4,500 - $15,000 |
| Roof Replacement (relevant when integrating window flashing) | $8,000 - $20,000 |
These are project-level ranges - a single sash repair or glass swap will cost a fraction of the full-install numbers. We write fixed quotes with line-item pricing, so the number you see is the number you pay. Call (844) 638-7249 and we will schedule a free estimate tailored to your exact PGT units and opening count.
Not if the window flashing and perimeter seal are handled correctly during the roof replacement. When we replace a roof on a Fort Myers home with existing PGT WinGuard or EnergyVue units, we coordinate the flashing tie-in at the head-of-wall so the roof-to-wall water barrier integrates with the window’s existing flange or fin seal without breaking the window’s drainage plane. We have performed this exact sequence on post-Ian reroofs across Lee County. The PGT window warranty is between you and PGT, but our workmanship is covered by our 730-Day Done Right Promise - if a flashing error causes water intrusion around the window within two years, we fix it at no charge.
Book Your PGT Service in Fort Myers, FL
If you have a PGT window that is fogged, binding, leaking, or just not operating the way it should, call us at (844) 638-7249. We answer with a live person, 24/7 - not a recording - and we will schedule your free estimate at a time that works for you. Derek Hollenbeck and our Fort Myers crew have been fixing PGT products across Lee County for years, and every repair comes with upfront pricing and the 730-Day Done Right Promise. We don’t just break ground - we build something worth standing on.
Written by Derek Hollenbeck, Owner at Groundwork Construction Co. of Fort Myers, serving Fort Myers and Lee County since 2014.