What Walk-In Showers & Shower Remodeling Runs in Pelican Bay - and How Long It Takes
Walk-in shower remodeling in Pelican Bay typically costs between $4,500 and $12,000, and most projects wrap up in four to seven working days. That range covers tearing out an existing tub or old shower pan, waterproofing to current Florida code, and installing a custom tile or solid-surface walk-in shower with new fixtures. Call (844) 638-7249 for a free on-site estimate with a written, line-by-line price - you’ll know exactly what you’re paying before any work begins.
We see Pelican Bay homeowners choose a walk-in shower remodel for two main reasons. First, many of the community’s condo towers and villas were built with fiberglass tub-shower combos that feel dated and cramped thirty-plus years later. Second, the sheer wear salt air puts on enclosures, grout, and plumbing trim means even a well-maintained original bathroom starts looking tired faster here than it would even a few miles inland. A properly waterproofed tile shower with Schluter or similar modern substrate systems is a different animal entirely - and it’s what we install the majority of the time.
How We Walk Through a Shower Remodel Job - Stage by Stage
Day one: protect, demo, and inspect. Before any hammer swings we run floor protection from your entry door to the bathroom and seal off the work zone with zip-wall containment. The old shower pan or tub, wall surround, and valve trim come out. If the subfloor or studs show water damage - a real possibility given how many Pelican Bay condo showers were originally built without proper waterproofing membranes - we stop and show you exactly what we found. You make the call on any structural or subfloor repair before we proceed. This stage takes most of the first day.
Rough-in and waterproofing. Once the cavity is clean and dry, our plumber adjusts the valve position and drain location if your new shower footprint requires it. We install the waterproof substrate system - sheet membrane or liquid-applied - across the entire wet area floor and walls per Florida Building Code. This is the step that separates a shower that lasts twenty years from one that rots out in five, and it’s the part we never rush. You decide on your tile layout and grout color during this phase so we’re locked in before setting begins. This stage is typically one full day.
Tile and pan installation. The shower pan is sloped and set, the wall tile goes up, and niches and benches are framed and waterproofed. We use epoxy grout on shower floors as standard - it resists the staining and efflorescence that Pelican Bay’s mineral-heavy water can leave behind in cement grout over time. Large-format wall tiles speed installation and reduce grout lines, but they also require flatter walls; we’ll flag that early so you can decide whether to pay for extra wall prep or shift to a smaller tile. Two to three days here depending on size and complexity.
Fixtures and glass. The shower valve trim, showerhead, and any body sprays or handhelds get installed and tested. When the glass enclosure is part of the project - and for most Pelican Bay walk-in remodels it is - our glass partner takes precise field measurements after all tile is set, then fabricates and installs about five to seven business days later. The shower is fully usable once the glass is in. Fixture trim-out is a half-day.
Final walkthrough and close-out. We pull the floor protection, clean the bathroom, and walk the finished shower with you. Every control gets demonstrated. Grout gets sealed if specified. Any punch-list items get noted and resolved. The entire project, start to finish, lands inside of two weeks except when custom glass lead time pushes the final install day by one week. You’ll have your shower back faster than you think.
Throughout the job you’ll reach a live person at (844) 638-7249 anytime - not a voicemail box - for questions or to adjust a detail. That matters when you’re living through a renovation.
The Choices You’ll Make on a Pelican Bay Shower Remodel
A walk-in shower has more decision points than most homeowners expect. Here are the ones that change the look, feel, and cost the most:
- Curbless versus curbed entry. A true curbless, barrier-free shower floor sits flush with the bathroom floor. It’s the cleanest look and works beautifully in master baths, but it often demands a recessed subfloor or a raised bathroom floor to get the required drain slope - adding labor and cost. A low-profile curbed shower costs less and drains perfectly with no subfloor surgery.
- Tile versus solid-surface walls. Porcelain tile gives you near-unlimited design options and holds up forever when installed over a proper waterproof substrate. Solid-surface panels (like cultured marble or acrylic systems) install in a day with zero grout lines, but color and texture choices are narrower. Tile prices in Pelican Bay average $8-$18 per square foot installed for a standard shower; solid-surface panels typically land in the $4-$10 range. Both can look sharp; the trade-off is design flexibility versus maintenance simplicity.
- Shower pan material. A site-built tile pan with a bonded waterproofing system gives you exact size flexibility and matches your wall tile. A pre-formed solid-surface pan cuts a day out of the schedule and eliminates grout on the floor entirely. We install both. If you’re in a condo where a pan leak means liability for the unit below, a solid-surface pan with an integrated flange is a smart conversation to have.
- Nichies and benches. A recessed shampoo niche and a corner bench are the two add-ons that Pelican Bay homeowners rarely skip. Each adds $400-$800 to the job depending on size and waterproofing complexity. We build niches with a slight inward slope so water never pools. Benches are framed from concrete block or waterproof foam - never wood - inside the wet area.
- Fixture trim level. A single-function pressure-balanced shower valve with one showerhead is your baseline. Stepping up to a thermostatic valve with volume control, a rain head, and a handheld on a slide bar changes the in-shower experience dramatically - and adds $700-$1,500 to the plumbing rough-in and trim package. We use Kohler and Delta valve bodies as our standards; they’ve proven reliable in Pelican Bay’s water conditions and parts are available locally if anything ever needs service years down the road.
What Walk-In Showers & Shower Remodeling Costs in Pelican Bay, FL
A stand-alone walk-in shower remodel in Pelican Bay typically runs $4,500 on the lower end for a straightforward acrylic or solid-surface replacement with standard fixtures, up to roughly $12,000 for a full custom tile shower with curbless entry, glass enclosure, and premium plumbing trim. The average job we do here falls around $7,500-$8,500.
Five variables do the most to move that number. First, whether you’re working inside the existing shower footprint or changing the layout - moving a drain line or a valve adds plumbing labor and wall opening. Second, the waterproofing substrate you choose; a full sheet-membrane system with a bonded drain costs more in materials than a traditional method but delivers a far drier wall cavity over the long haul. Third, tile selection matters: a basic 12×24 porcelain costs about half what a hand-glazed or large-format slab tile runs. Fourth, glass enclosure configuration - a single fixed panel is the simplest, cheapest option; a full frameless door with a transom is the high end. Fifth, whether this is a standalone shower remodel or part of a wider Bathroom Remodeling in Pelican Bay scope - bundling the shower with flooring, vanity, and lighting often reduces the per-item cost.
Every estimate we write is a fixed-price, line-item document. You’ll see the cost of demo, plumbing rough-in, waterproofing, tile labor and materials, fixtures, glass, and any structural or drywall repair. No “allowance” line items that balloon later. No change orders unless you choose to expand the scope. The price you see is what you pay, backed by our 730-Day Done Right Promise: if we miss something, we make it right at no additional cost.
What Pelican Bay Homes Specifically Bring to a Shower Remodel
Most walk-in shower projects we take on in Pelican Bay happen inside mid-rise and high-rise condominium units built from the mid-1980s through the early 2000s. That building age tells us four things before we even open a wall. The original shower construction rarely included a waterproofing membrane on the walls - tile was often set directly on green board or cement board with no moisture barrier behind it. The plumbing valves are original and, in many cases, not pressure-balanced by today’s code. The subfloor is post-tension concrete slab, which means we cannot cut or core anywhere without current engineering drawings identifying the tendon layout - sever a live tendon and the repair is six figures. And the building may have HOA or condominium association requirements around work hours, material delivery routes, and insurance certifications that a contractor running a single-family home project never sees.
Collier County permitting also applies: a shower remodel that moves the drain or alters the valve configuration requires a plumbing permit and inspection. We pull the permit, schedule the inspection, and stand with the inspector during the visit. You won’t chase paperwork. Our crew has worked inside enough Pelican Bay towers to know that some buildings have water shutoff valves at the unit, some at the riser, and some require building engineering coordination for a brief whole-riser shutoff - we sort that out before day one so there are no surprises.
Salt air is the quieter variable here. Exposed plumbing trim, shower door hinges, and even some metal drain grates corrode faster in beachfront and near-beach buildings than in properties set back along the interior of Pelican Bay. We spec electroplated or PVD-finished fixtures as standard on these jobs - the upcharge is modest and it buys years of clean appearance that a basic chrome finish won’t deliver within a half-mile of the Gulf.
If your project scope grows beyond the shower and you’re considering the roof or exterior at the same time, we frequently coordinate Roof Replacement & Installation in Pelican Bay so that any interior drywall or ceiling work from a roof leak gets addressed in one cohesive phase. Some homeowners also use a major interior renovation as the right moment to upgrade to a Metal Roofing in Pelican Bay system - the interior is already protected during construction, and bundling trades saves on mobilization costs.
Serving Pelican Bay, FL - Our Local Coverage Area
We’re based in the Pelican Bay area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked - Walk-In Showers & Shower Remodeling in Pelican Bay
Most Pelican Bay shower remodels take four to seven working days of on-site labor, with a possible extra week if custom glass enclosure fabrication is involved. Demo, plumbing rough-in, and waterproofing fill the first two days. Tile and pan installation runs two to three days. Fixture trim-out is a half-day. Glass, if ordered, is measured after tilework is complete and typically installed five to seven business days later. The shower is fully usable the day the glass goes in.
Collier County requires a plumbing permit if you move a drain, alter a valve location, or change the shower footprint in any way that affects the plumbing system. A like-for-like fixture replacement with no plumbing relocation generally does not require a permit, but we pull one anyway when waterproofing inspection is part of the scope - it protects you down the line. Groundwork Construction Co. handles the permit application and scheduling, and a uniformed, background-checked technician is present for every inspection. Call (844) 638-7249 and we’ll tell you whether your specific project triggers a permit requirement.
Yes, and that’s the most common scenario in Pelican Bay condo remodels where the drain is embedded in post-tension concrete and moving it would require engineering coordination. We build the new shower inside the existing drain and valve footprint, which keeps cost and timeline low while still giving you a fully custom tile or solid-surface finish with modern waterproofing. If your layout demands a different drain location, we’ll bring in the structural drawings first - cutting into a post-tension slab without them is a non-starter.
A walk-in shower remodel in Pelican Bay typically runs $4,500 to $12,000. The spread reflects whether you choose an acrylic or solid-surface system versus full custom tile, whether the entry is curbed or curbless, and the level of plumbing trim and glass enclosure you select. Our estimates are fixed-price and line-item - you’ll know exactly what’s covered before you sign. Call (844) 638-7249 to schedule a free on-site estimate with no obligation.
Every walk-in shower we install is covered by the Groundwork Construction Co. 730-Day Done Right Promise. If something isn’t right - a grout issue, a leak, a fixture defect tied to our installation - we fix it at our cost within two years of completion. The waterproofing substrate manufacturers we use (Schluter and similar) carry their own material warranties that extend well beyond that window. Between the two, you’re not left holding the bag on a shower that underperforms.
Get a Straight Price on Your Pelican Bay Walk-In Shower Remodel
When you’re ready to see what a walk-in shower remodel actually costs for your specific bathroom, call (844) 638-7249. We’ll schedule a free on-site walkthrough, measure everything, talk through your material and layout preferences, and hand you a written, line-by-line estimate - usually within 48 hours of the visit. No pressure, no vague ballparks, no change-order games. Just a real price and a clear timeline from a team that knows Pelican Bay’s condo buildings and building code inside out.
Written by Derek Hollenbeck, Owner at Groundwork Construction Co., serving Pelican Bay and surrounding communities with upfront pricing and the 730-Day Done Right Promise.