What a Tub-to-Shower Conversion in Verona Walk Actually Costs and How Long It Takes
A tub-to-shower conversion in Verona Walk typically runs between $3,500 and $10,000, with most jobs landing around $5,500 to $7,200 for a standard alcove replacement using mid-grade materials. The work takes three to five business days from demolition to final silicone cure. If you’re standing in a guest bath with a tub nobody’s used in five years, call (844) 638-7249 for a free on-site estimate - we’ll give you a written, line-item price before you commit to anything.
How We Convert a Bathtub to a Walk-In Shower - The Real Sequence
Day 1 - Demo, Inspection, and the Inevitable Surprise
We pull the tub, strip the surround to bare studs, and shut off water at the local valves. In a DiVosta home - and nearly every residence in Verona Walk is DiVosta-built - this is the moment we inspect the poured-concrete wall behind the alcove for any signs of moisture wicking through. These solid walls don’t harbor rot the way framed walls do, but any plumbing leak that’s been quietly seeping gets caught here. We cap and pressure-test the supply lines and open the drain to confirm we can tie into the existing 2-inch pipe without relocating it. You’ll make your final call on the shower base - acrylic pan or tiled floor - by 3 p.m. so materials staging starts first thing tomorrow.
Day 2 - Rough-In and Waterproof Substrate
If the existing drain location stays put, we rough in the new shower valve and any accessory plumbing (a handheld slide bar, a second showerhead on a diverter - decisions we’d have walked you through during the estimate). The alcove gets a full-coverage waterproofing system: either a bonded sheet membrane or a liquid-applied sealant that meets Florida Building Code Chapter 15 for wet areas. This is non-negotiable. Any contractor skipping this step in Verona Walk is leaving you with a mold problem inside a concrete-walled home that doesn’t dry out through the walls the way wood-frame construction does. The shower pan or prefabricated acrylic base goes in once the waterproofing cures.
Day 3 - Wall Board, Tile Set, and Niches
Wall board goes up (cement board, never green board), seams are taped and sealed, and tile setting begins. This is typically the longest single day of the project. A standard 60-inch alcove with 12×24 porcelain running to the ceiling and a recessed niche framed into the back wall takes one full day of tile work. If you opted for a hexagonal mosaic floor paired with a prefab pan, the pan was set yesterday and the mosaic goes in this afternoon. Grout happens in the final hour once tile adhesive has set firm.
Day 4 - Fixture Trim-Out and Glass Enclosure Templating
Showerhead, valve trim, handheld, and controls are installed and tested. We run the shower for 15 minutes with the valve fully open to confirm drainage speed and check for any leaks behind the wall - a pressure test on day one and a live-water test on day four mean there are zero surprises after we leave. If the project includes a frameless glass enclosure, the fabricator arrives late afternoon to laser-template the opening. That glass typically takes 7-10 days to fabricate. You’ll have a fully functional shower with a temporary rod and curtain while you wait; no gap in use.
Day 5 - Glass Install and Final Walkthrough
If the enclosure was templated earlier in the week, the glass crew installs it today. We silicone all perimeter joints, clean the tile and grout, patch any drywall scuffs from demolition, and walk you through every detail: valve operation, drainage, grout maintenance, and the warranty paperwork. The shower is ready to use within 24 hours once silicone has fully cured.
The Options You’ll Choose Between
- Acrylic or fiberglass shower base vs. tiled floor. A solid-surface pan installs in under two hours, never needs sealing, and keeps the project at the lower end of the price range - usually $3,500 to $5,500 all-in. A tiled floor with a mortar-bed slope looks higher-end, costs $1,200 to $2,000 more, and requires annual grout sealing. In Verona Walk, where the water is moderately hard, a textured acrylic pan also means fewer mineral deposits to scrub off tile grout lines.
- Wall tile material. Porcelain is the default - it’s dense, nearly waterproof, and holds up to Collier County humidity without efflorescence. Ceramic costs a little less upfront but absorbs more moisture and chips more easily at cut edges. Natural stone like marble or travertine is absolutely an option but pushes the job north of $8,000 and demands more ongoing maintenance. We’ll source slabs and tile from suppliers we’ve worked with for years, not whatever’s on clearance at a big-box aisle.
- Shower door configuration. A framed sliding door is the most cost-effective at $400-$700. A frameless hinged door with 3/8-inch tempered glass runs $900-$1,400 depending on width. A full custom enclosure with a stationary panel and door can reach $2,200. Every Verona Walk HOA we’ve worked with is primarily concerned with exterior alterations - interior glass style isn’t an approval item - so you’re free to choose what works for your budget and sightlines.
- Accessories and niche layout. Recessed niches, corner shelving, bench seating (a floating corner bench or a prefab teak seat), and grab-bar blocking are easier and cheaper to install during the rough-in than to retrofit later. If you’re planning to age in place inside your Verona Walk home, we recommend adding blocking for at least one grab bar and a handheld shower slide bar on a 60-inch hose during this conversion - it adds under $300 in materials and labor now versus a $1,200+ tear-out later.
What a Tub-to-Shower Conversion Costs in Verona Walk, FL
Our projects here range from $3,500 to $10,000. The spread exists because identical-looking alcoves hide very different conditions once the tub is out. Here’s what actually moves the number.
Existing plumbing location. If the drain and supply riser stay right where they are, you’re on the low end. Relocating a drain by even 12 inches - which some layouts require if you want a centered shower rather than an offset one - means opening the slab and re-routing PVC inside a poured-concrete floor. That’s a $900 to $1,700 adder in a DiVosta home. It’s not optional if the configuration demands it, but it’s the single biggest variable in any tub-to-shower conversion we price in Verona Walk.
Waterproofing method. A liquid membrane is faster and slightly cheaper. A full sheet membrane system costs $400-$700 more in materials and labor but carries a longer manufacturer warranty. In Florida humidity, we lean toward sheet membranes in alcoves that back up to exterior concrete walls, where condensation risk is higher.
Tile and finish grade. Builder-grade 12×24 porcelain in a single color with a basic bullnose edge stays under $5,500. A mixed-format layout with a mosaic accent band, a custom niche, and a frameless enclosure pushes past $7,500. Ceiling-height tile (recommended in Verona Walk - steam and moisture rise inside a sealed concrete home faster than in a vented wood-frame house) adds roughly $400-$600 in tile and labor compared to stopping at showerhead height.
Permit scope. A straightforward fixture swap with no drain relocation usually qualifies as a like-for-like replacement under Collier County code and may not require a full plumbing permit. Once the drain moves, a permit is required, inspections are scheduled, and the job adds $200-$400 in fees and a half-day of schedule coordination. We pull permits when they’re required - no shortcuts, no “we’ll handle it under the table” nonsense.
Every estimate we write is a fixed-price quote - the number on the page is the number you pay, period. It includes demolition, disposal, plumbing rough-in, waterproofing, tile or acrylic surround, shower base, fixtures, trim-out, and a final clean. It does not include structural wall alterations beyond the alcove, relocation of a toilet or vanity, or full-floor tile outside the shower footprint - those belong on a larger Bathroom Remodeling in Verona Walk scope, and we’ll tell you honestly if your project has crossed that line.
What Verona Walk Homes Specifically Do to This Job
Verona Walk is a near-total DiVosta community. The homes here - built largely between 2004 and 2009 - use a poured-concrete wall system that has no hollow cores to fish plumbing through. Most tub alcoves are set against an interior wall, not an exterior one, which is good news: we’re rarely opening a structural concrete panel for a tub-to-shower conversion. The bad news is that any drain relocation in a ground-floor bath means cutting through a concrete slab floor poured integrally with the wall footers, not a separate slab. It’s entirely doable with the right core-drilling equipment (which our crew runs regularly), but it’s loud, it’s dusty, and it takes a full extra day compared to a wood-joist subfloor. If you’re on the second floor, joists are accessible - the job moves faster and costs less. We also factor in HOA architectural review timing: while an interior remodel typically doesn’t trigger the same review as an exterior alteration, some Verona Walk sub-associations want notification if plumbing changes affect the unit’s overall system. We’ll help you navigate that during the estimate so there are no stop-work surprises.
One pattern we see repeatedly in these homes: the original DiVosta tubs were installed with a thin bead of silicone against a painted drywall flange, and by year 15, that seal has failed in the corners where the tub apron meets the wall. The result is slow, invisible moisture migration into the adjacent baseboard and drywall. When we pull the tub, we often find the bottom 6 inches of drywall are soft. It’s not a catastrophic leak - it’s just age - but it means our project scope regularly includes replacing the lower drywall section and re-taping the seam before waterproofing begins. We’ll spot it during demolition and show you exactly what we’re seeing before we proceed. This is also the moment some homeowners decide the whole room deserves an update, and that’s where our Bathroom Remodeling team can pivot the scope - but if it’s just the alcove, we keep it tight and finish on schedule.
Serving Verona Walk, FL - Our Local Coverage Area
We’re based in the Verona Walk area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked - Tub-to-Shower Conversion in Verona Walk
Three to five working days for the construction phase. If a custom glass enclosure is part of the job, the glass arrives 7-10 days after templating, but the shower is fully usable with a temporary rod and curtain during that wait. Permits, if required, add a few days of lead time before we start.
It depends on whether plumbing locations change. A direct swap - same footprint, same drain location - typically qualifies as a repair and may not require a plumbing permit. Moving a drain, adding a second showerhead on a new diverter, or altering any waste line in the slab triggers a permit requirement. We’ll determine which applies during the estimate and pull the permit if it’s needed. We carry the license to do the work correctly either way.
In most Verona Walk alcoves, yes. A standard 60-inch tub drain sits at the far end, and we can set a shower base or slope a tile floor to drain at the same point. The showerhead stays on the same wall the tub spout occupied, so the supply riser doesn’t move either. This keeps the project fast and keeps costs in the $3,500-$5,500 range. If you want the drain centered for a more balanced look, that’s when the slab work starts.
A $3,500-$4,500 project in Verona Walk is typically: demolition, no drain relocation, an acrylic shower base, a single acrylic or fiberglass surround (no tile), a standard showerhead and pressure-balanced valve, and a framed sliding door. A $9,000-$10,000 project includes: tile walls to the ceiling with a porcelain or natural stone finish, a mortar-bed tiled floor, a frameless glass enclosure, a recessed niche with accent tile, a handheld slide bar, and possibly upgraded valve trim in a finish like brushed nickel or matte black. The difference is almost entirely in materials and the labor hours to install them.
Every tub-to-shower conversion we do in Verona Walk is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right - no fine print about “water damage excluded” or “installation only.” The waterproofing system underneath the tile or surround is warrantied by the manufacturer for its rated lifespan, and our laborship warranty runs alongside it. Calls are answered by a live person, 24/7, at (844) 638-7249 - you won’t get a voicemail black hole if a question comes up six months after the job is finished.
Get a Fixed-Price Estimate for Your Tub-to-Shower Conversion in Verona Walk
Come to the estimate with questions and a budget in mind, and we’ll come with samples, a laser measure, and straight answers. We’ll walk the alcove, check the slab situation, and hand you a written quote that won’t change once work starts - upfront pricing, no surprises. Financing is available at 0% for 18 months on qualified projects, and we’ll schedule your start date before we leave. Call (844) 638-7249 to set up a free on-site estimate. Our Bathroom Remodeling crew handles everything from the first cut to the final silicone bead, and we’ve been doing it long enough that a Verona Walk address tells us most of what we need to know before we even pull into the driveway. Some homeowners pair the shower conversion with exterior upgrades - Metal Roofing in Verona Walk or Tile Roofing in Verona Walk - and we can coordinate those scopes as a single project if you’re tackling multiple improvements at once.
Written by Derek Hollenbeck, Owner at Groundwork Construction Co., serving Verona Walk with fixed-price remodeling and a 730-Day Done Right Promise.