What Vanities, Tile & Fixtures in Marco Actually Costs and How Long It Takes
A bathroom vanity, tile, and fixture upgrade in Marco typically runs between $9,000 and $28,000, with most jobs wrapping in two to three weeks. That range covers swapping a single vanity, new floor and wall tile, and updating faucets, shower trim, and lighting fixtures. The biggest spread comes down to whether we’re working with existing plumbing locations or moving drain lines and supply stacks, something that gets complicated fast in the older concrete-slab homes across Marco. Call (844) 638-7249 for an on-site estimate with a written, line-by-line scope breakdown.
How We Handle Vanities, Tile and Fixture Jobs From Start to Finish
Most homeowners only do a vanity, tile, and fixture refresh once or twice, so the sequence isn’t obvious. We walk you through it before we ever swing a hammer, and nothing gets ordered until every choice is locked in writing. Here’s how the work actually unfolds.
Stage 1: On-Site Walkthrough and Scope Lock
We come to your Marco home, measure every wall, and map the existing plumbing. This is where we flag what can stay put and what has to move. On a typical Deltona-era concrete-block ranch, the drain stack is cast iron set in the slab, so relocating a vanity from one wall to another means cutting concrete, something that adds real cost and days to the timeline. We give you a fixed price from these measurements, not a ballpark. Decisions you’ll make here: vanity width, single or double sink, and whether fixtures stay in the same footprint.
Stage 2: Material Selection and Ordering
We bring samples to you or meet you at a supplier showroom in the Fort Myers area. You’ll pick the vanity (stock, semi-custom, or custom), cabinet finish, countertop material, tile size and layout pattern, grout color, faucet finish, shower trim kit, and light fixtures. Lead times on semi-custom vanities run four to eight weeks right now; custom can push twelve. We order everything the day you approve the selections and don’t tear anything out until it’s all in hand.
Stage 3: Demo and Plumbing Rough-In
This takes one or two days. We disconnect and remove the old vanity, pull up floor tile, and strip wall tile down to the substrate. If plumbing is staying put, we cap and prep stub-outs. If we’re moving drain locations in a Marco slab home, day two is concrete saw-cutting, trenching, and running new PVC to the stack, followed by patching the slab. Our crew is background-checked and uniformed, and we protect your floors and hallways with full dust containment from start to finish.
Stage 4: Tile, Vanity Set, and Fixture Trim-Out
Floor tile goes down first, typically over a decoupling membrane to handle the minor slab movement common in Marco’s older homes. Wall tile follows, using waterproof backer board in wet areas. Once tile is set and grouted (budget three to five days depending on square footage and pattern complexity), we install the vanity, attach the countertop, and mount faucets. The plumber returns to connect drain assemblies and supply lines. Electricians swap light fixtures and fan units. This stage ends with a fully functioning bathroom, minus final touches.
Stage 5: Final Walkthrough and the 730-Day Sign-Off
Derek Hollenbeck or a lead project manager walks the job with you. We test every faucet, drain, and fixture. Grout gets inspected under real lighting. If anything isn’t right, it gets fixed before we consider the job complete. Every vanity, tile, and fixture project we do in Marco is covered by our 730-Day Done Right Promise: if something fails due to our workmanship within two years, we come back and make it right at no charge. That guarantee is in writing, not a handshake.
The Options You’ll Choose Between
Vanities, tile, and fixtures are the three categories where your choices drive the final number more than anything else. Here’s what you’re actually deciding, with the honest trade-off on each.
- Vanity type. Stock vanities from big-box suppliers land in the $800-$1,500 range but limit you to standard widths (24, 30, 36, 48, 60 inches) and a handful of finishes. Semi-custom cabinets let you pick door style, paint or stain color, and hardware, usually running $1,800-$4,500 depending on size and material. Fully custom built vanities, built to the inch with solid hardwood and dovetailed drawers, start around $3,500 and can exceed $7,000 for larger double-sink units. Custom takes longer but fits odd wall dimensions perfectly, a real advantage in Marco’s older bathrooms that were rarely framed with standard cabinet widths in mind.
- Countertop surface. Cultured marble and solid-surface tops are the budget-friendly picks at $300-$800. Quartz runs $600-$1,800 and resists staining and salt-air moisture better than natural stone, which matters when your bathroom opens to a humid Marco canal breeze. Granite and marble look great but need sealing every year in our climate. For a guest bath that sees light use, cultured marble is fine. For a master bath you’re using daily, quartz is the smarter long-term buy.
- Tile material and layout. Ceramic wall tile starts around $3 per square foot installed. Porcelain floor tile runs $6-$12 installed, with large-format slabs (24×48 and up) adding labor because they’re harder to cut and set precisely. Natural stone like travertine or marble pushes past $15 per square foot but delivers a look that’s hard to match. Pattern matters: a running bond or straight lay is fast; herringbone, hexagon, or basketweave layouts add 30-50% in labor. For Marco bathrooms, we lean toward porcelain with a high PEI wear rating and low water absorption. It holds up better in the humidity and doesn’t effloresce the way some natural stones do near the coast.
- Fixture finish and trim. Chrome and brushed nickel are the most affordable and hold up fine against salt air if wiped down regularly. Matte black and polished brass cost more and show water spots faster. The real money decision is shower trim: a basic single-handle pressure-balance valve kit is $150-$300, while a thermostatic valve with multiple body sprays and a rain head can hit $1,500 in hardware alone. For a simple vanity-and-fixture refresh where you’re not touching the shower, the fixture cost is mostly faucets and drain assemblies, usually $200-$600 total.
- Lighting and electrical. Vanity light bars and sconces range from $80 to $400 per fixture. If you’re adding a dedicated circuit for a heated floor, a humidity-sensing exhaust fan, or relocating a switch, the electrical scope grows. Most vanity swaps don’t need a new circuit, but if the existing wiring is original 1960s aluminum, we’ll flag it during the walkthrough. Rewiring is a separate line item but worth doing while the walls are open for tile.
What a Vanity, Tile and Fixture Project Costs in Marco, FL
You’ll pay $9,000 to $28,000 for a bathroom vanity, tile, and fixture upgrade in Marco, with most jobs settling between $14,000 and $19,000. That’s the honest spread. Here’s what pushes a job toward the low end or the high end.
Plumbing relocation. In Marco’s slab-on-grade homes, the drain stack is buried in concrete. If the new vanity sits in the same footprint as the old one, plumbing cost is minimal. Moving a drain more than a few inches means cutting the slab, which can add $1,200 to $3,000 to the job depending on how far the pipe has to run and whether the existing cast iron is in good enough shape to tie into.
Tile square footage and demo. Tile cost scales linearly with area, but demo doesn’t. Pulling up old tile over a slab and grinding the thinset residue is dusty, loud work that takes a couple of days for a typical Marco bathroom. If the original tile was set with wire lath in a mortar bed, demolition time doubles and disposal weight adds to the dump fee. Budget $1,800-$4,000 for full floor and wall tile replacement in an average 5×8 bathroom.
Vanity size and configuration. A single 30-inch stock vanity with a cultured-marble top might run $1,200 installed. A custom 72-inch double vanity in painted maple with a quartz top and undermount sinks can hit $5,000-$7,000 installed. That’s the widest single variable in most budgets.
Permit scope. A straight swap of vanity, tile, and fixtures in the same locations typically doesn’t trigger a permit in Collier County beyond a simple fixture replacement. If we’re moving the vanity, adding a new circuit, or altering the wet wall, we pull the permit and coordinate the inspection, and that cost is line-itemed in your estimate. We don’t hide permit fees in a lump sum. Everything is upfront pricing, no surprises.
Every estimate from us is a written, fixed-price quote that breaks out materials and labor separately. No change orders unless you change the scope mid-job. Call (844) 638-7249 for a free, no-obligation estimate at your Marco home.
What Marco Homes Do to a Vanity, Tile and Fixture Job
Marco Island’s housing stock is unlike anything inland. The dominant homes are Deltona-era concrete block ranches built on slab foundations in the 1960s and early 1970s, and they share a handful of traits that directly shape a vanity and tile project. Those slabs mean any vanity drain relocation is a concrete-cutting operation, not a crawlspace job. The cast-iron drain stacks in these homes are sixty years old and often corroded at the hub, so we pressure-test them before committing to a tie-in. Humidity and salt air from the Gulf and the canal grid accelerate the failure of cheap MDF vanity cabinets, which swell and delaminate at the base within a few years. We spec plywood-box construction with moisture-resistant finishes for every Marco install for that exact reason.
The substantial-improvement rule under Collier County code also hangs over larger projects here. A vanity, tile, and fixture refresh on its own rarely crosses the 50% threshold, but if you’re pairing it with other work, the math matters. We’ve had homeowners in the Caxambas and Old Marco neighborhoods call us for a bathroom update and end up discussing whether their renovation path triggers a full Bathroom Remodeling in Marco conversation. On its own, though, the vanity and tile job is straightforward, permitted when required, and finished on a timeline we commit to in writing before the first day of demo.
Some homeowners in Marco pair this interior work with exterior upgrades like Tile Roofing in Marco or Specialty Roofing in Marco, especially when they’re renovating a canal-front property ahead of listing season. Our bathroom remodeling crew coordinates directly with any other trades on site so you’re not managing multiple schedules.
Serving Marco, FL - Our Local Coverage Area
We’re based in the Marco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Vanities, Tile and Fixtures Questions in Marco
Two to three weeks from demo to final walkthrough, assuming materials are on site and the vanity footprint isn’t moving. Custom or semi-custom vanities add lead time before work begins, typically four to eight weeks for ordering, but that doesn’t extend the on-site portion. Moving a drain in a slab adds two to three days for concrete cutting and repair.
For a direct swap with no plumbing relocation and no electrical changes, typically no. If we’re moving the vanity drain, adding or moving an outlet, or altering the wet wall inside the stud cavity, we pull the permit through Collier County and schedule the required inspections. We’ll tell you during the walkthrough whether your specific scope triggers a permit, and that cost is always a separate, transparent line item.
Sometimes, but usually not. A double vanity needs two drain stub-outs centered roughly 30 inches apart. Most single-vanity rough-ins in Marco’s older homes have one drain stack off-center. If the existing drain happens to be in the right spot and we can tee off it, you’re in luck. In most cases, going from single to double means cutting the slab to add a second drain, which adds cost and time. We’ll give you a firm answer during the estimate, not after demo starts.
Porcelain with a water absorption rate under 0.5% and a PEI rating of 3 or higher. It won’t absorb moisture from the air the way natural stone can, and it’s dense enough to resist cracking on a slab that shifts slightly with temperature cycles. We use epoxy or polymer-modified grout on every Marco job. Standard cement grout wicks moisture and grows mildew in a bathroom that stays humid eight months of the year. For wall tile outside the wet zone, ceramic is fine and costs less.
Every vanity, tile, and fixture job we do in Marco is backed by our 730-Day Done Right Promise. If workmanship fails within two years, we fix it. Manufacturer warranties on the vanity, countertop, faucets, and tile vary by brand, and we walk you through those terms when you’re selecting materials. The vanity cabinet finish, for example, may carry a one-year or five-year warranty depending on whether it’s stock or custom. None of that fine print shortens our two-year labor commitment. Call (844) 638-7249 for a free estimate and a written warranty summary before you sign anything.
Get a Fixed-Price Estimate for Vanities, Tile and Fixtures in Marco
If you’re ready to upgrade a tired bathroom with a new vanity, fresh tile, and updated fixtures, we’ll give you a written, no-surprises estimate at no charge. Call (844) 638-7249 to schedule a walkthrough at your Marco home. A live person answers and we’ll have a project lead at your door with samples, measurements, and straight answers about timeline and cost.
Written by Derek Hollenbeck, Owner at Groundwork Construction Co., serving Marco since 2014.